MIXX AND CLICK

Sliding hammer 180 mm, 200 g - GEDORE 1.35/0 - 1958062 Suited for the removal of small ball bearings since there is often not enough room for counter-support braces Can also be used with threaded inserts no. 1.81

Internal extractor 5-8 mm - GEDORE 1.30/0 - 8012750 For extremely-tightly-packed ball bearings, bearing races, bushings, and shaft seals Simmering® Operation: The internal extractor is inserted into the bearing and the spindle screwed in. The sharp turned-out shoulders of the pulling shell jaws will press outwards behind the part to be extracted. The counter-support brace is then added. Both feet must be aligned parallel to the spindle to ensure rigidity. The design can vary from the image Can be used with either sliding hammer or counter-support brace (*) min. and max. dimension in idle and spread state

Internal extractor 12-14 mm - GEDORE 1.30/2N - 8013050 Especially suitable for the safe and trouble-free extraction of needle roller bearings, ball bearings and brass sleeves from crankshafts Note: The soulder of the shell jaw must be applied behind the bearing

Spare leg for 1.30/10 and 1.30/10N - GEDORE 130/10-200 - 2827565 One spare hook including screws Suitable for 1.30/10 and 1.30/10N Recommendation: In case of a broken hook, all three hooks should be replaced

Counter-support brace for 1.30/0 - 1.30/5 - GEDORE 1.36/1 - 8016580 • Operation: The counter-support brace is placed on the housing and the spindle screwed onto the spindle of the internal extractor. The toggle is held firmly, and the bearing extracted by tightening the nut.

Internal extractor 5 - 8.5 mm - GEDORE 1.34/1 - 1638556 For use with sliding hammer no. 1.35/0 or counter-support brace no. 1.36/1 Multiple wrench size (11 + 13 mm)

Internal extractor set - GEDORE 1.31/0 - 8014530 Sets comprise the most used extractor sizes for the removal of ball bearings, bearing races, bushings, shaft seals, etc. In handy sheet metal case

Internal extractor set - GEDORE 1.34/10 - 1638629 For tightly-fitting ball bearings, bearing races, bushings and shaft seals Titanium-nitrided surface Multiple wrench size (11 + 13 mm) M10 connecting thread Operation: The internal extractor is inserted into the bearing and the spindle screwed in. The sharp turned-out shoulders of the pulling shell jaws will press outwards behind the part to be extracted. The counter-support brace or the sliding hammer is then added. In plastic case

Internal extractor reinforced shoulder 60-160 mm - GEDORE 1.30/10N - 2724804 Suitable for removing large ball bearings and bearing outer races Operation: The extraction jaws are spread by turning the nut. The newly-developed spreading system enables a simple, step-free and time-saving adjustment to the desired diameter to be made. The sharp-edged sections of the extraction jaws seat flush beneath when spread Both internal extractors can be used with sliding hammer 1.35/3 Adapter 135/325-I M16x1,5 G 1/2" (Code 1123750) must also be ordered if sliding hammer 1.35/3 is used.

Cylinder liner puller - GEDORE 1.37/2 - 8017200 Wet heavy-vehicle (e.g. Mercedes Benz, MAN) cylinder liners, automobile and stationary-engine liners, and other parts may be extracted using this puller Operation: The spindle of the counter-support brace is screwed into the clamping nut of the puller, and the puller inserted into the liner. The counter-support brace is placed on to the cylinder block. Due to the newly-developed spreading system, when the spindle is turned, all three jaws spread quickly and without difficulty, until they are firmly seated beneath the edge of the liner. Then the nut of the counter-support brace is tightened.

Internal extractor set, in L-BOXX 136 - GEDORE 1100-1.30 - 2836041 For Ø 12 - 35 mm For extremely-tightly-packed ball bearings, bearing races, bushings, and shaft seals Simmering® Sliding hammer 1.7 kg and counter-support brace 1100 CT2-1.30 to retrofit existing L-BOXX®es 136 With Check-Tool insert for quick check of completeness As tools are fully sunk in the foam, the equipped insert can be stacked Insert for use in drawers with min. dimensions 400 x 310 x 60 mm Contents: 1x Internal extractor set, in 2/2 L-BOXX 136 Module 1100 CT2-1.30 GEDORE 1100 CT2-1.30 (2836025) 1x GEDORE L-BOXX 136 empty, 442x357x151 mm 1100 L GEDORE 1100 L (2823691)

Set of internal and external extractors - GEDORE 1.32/1 - 8015260 • The handy sheet metal case comprises internal extractors, support braces, pulling chucks, external extractors and stud extractors