
Spindle summary
- Cutting tools
- Cutting + Grinding
- Hand tools
- cobit Bits + Accessories
- GEDORE Hand tools
- Spanners
- Sockets Range
- Screwdrivers
- Tool Modules
- Mobile Tool Storage
- Insulated Safety Tools 1000 V
- Pliers range
- Tool Assortments
- Torque Tools
- Bit range
- Workshop Equipment
- Impact Tools
- Striking Tools
- Forging Tools
- Pullers
- Separators
- MIXX AND CLICK
- Cartridge spanner
- Special Automotive Tools
- External Puller 3-arm
- Separators
- External Puller 2-arm
- Safety cover
- 2-/3-arm Universal Pullers
- Spindle summary
- Ball joint pullers
- External Puller 2-arm
- External Puller 2-arm
- Track alignment gauge
- 2-/3-arm Universal External + Internal Pullers
- Bearing assembly
- Hydraulic implements
- Spindle pressure pads / Adaptors
- Add-on systems
- Ball bearing extractors
- External Puller 2-arm
- Zubehör
- Coil Sping Compressors
- Oil filter hook
- Spindle pressure pads / Adaptors
- Pipe Bending Systems
- Hammers
- Pipe- and Tube-Working Tools
- Workshop Supplies
- Forestry tools
- Masonry tools
- WILPU Hand saws
- Measuring + Testing
- Promotions + Novelties

3
Variants
Extension for hydraulic spindle 1.06/HSP1-3, L35/60 mm - GEDORE 1.06/HSP-35V - 2824787 Extension for hydraulic spindle 1.06/HSP1-3, L35/60 mm
From €54.30*

Hydraulic press, 8 t - GEDORE 1.55/1 - 8024090 This piece of auxiliary equipment considerably increases the capability of the standard pressure spindle Operation: With pressure released, the press is placed between the pressure spindle and the end of the shaft. The pressure spindle is then tightened firmly. Care must be taken that the centreline of the shaft, the hydraulic press, and the pressure spindle are exactly in alignment. Then the hydraulic spindle is screwed inwards. Important note: Release the hydraulic press after use
€237.65*

3
Variants
Hydraulic pressure spindle 10 t - GEDORE 1.06/HSP1 - 8116100 For controlled and safe pulling work Set up for a pressure of 10 t, 12 t or 15 t The pressure piece can be replaced by a tip and lengthened, as required. The small pressure spindle is secured with an unscrewing lock to stop any accidental withdrawal. Preparation for use: 1. Before using, check whether the pressure spindle is screwed far enough out of the cap, so that the pressure pad is in the initial position in the hydraulic cylinder. 2. Unscrew the cap from the spindle body. For this purpose, first slacken off the grub screw. 3. Screw the spindle body from beneath into the cross piece of the puller until the body protrudes approx. 60 mm from the cross piece. 4. Screw the cap onto the spindle body until the stop, and then fix it in position by turning in the grub screw. Use and operation: e.g. HSP3 5. Place the puller into position and pre-tension the spindle body using a size 41 mm wrench. 6. Screw the pressure spindle size 17 mm into the cap. The hydraulic effect will come into use. The stroke of the pressure pad in the hydraulic cylinder is max. 12 mm. The workpiece that has been loosened by the hydraulic force may be pulled off completely by turning the spindle body with the cap size 41 mm. 7. Following its use, the pressure spindle (size 17 mm) is turned back into its initial position and the pressure pad pushed into the hydraulic cylinder.
From €391.41*
Lorem ipsum dolor sit amet
frontend.navigation.page
Lorem ipsum dolor sit amet
frontend.navigation.page




